Parts List and Assembly Instructions for Meteor Cam Mark III 12-29-2009 Approx. cost: 250 USD exclusive of Section 3.0 parts and capture and editing software 1.0 Camera, lens, dust cap and weather proof housing Utilitech No. 042122 120V 75W Halogen Landscape Light (Lowes, watertight housing for camera) http://www.lowes.com/lowes/lkn?action=productDetail&productId=42122-337-SP100PCUT Edmund Optics Micro Video Lens 1.68mmFL, No IR-Cut Filter M12 thread (Edmund online order) http://www.edmundoptics.com/onlinecatalog/displayproduct.cfm?productID=2196 Supercircuits PC402UXP Video camera board (Supercircuits mailorder) http://www.supercircuits.com/Security-Cameras/Board-Cameras/PC402UXP 8 1/2" x 11" piece of black construction paper (Art supply store) Plug-n-pull foam scrap (5" x 4") (Photo supply house) Duct tape Rubber sewer terminator cap with adjustable clamp for dust cover (Ace Hardware) Tools: Smaller wire cutter, scissors, hack saw (cut reflector), Phillips head screwdriver; flat head screwdriver; serrated kitchen knife; pencil compass; dab of flexible bathtub caulk; flathead microscrew driver; lens cleaning solution; lens cleaning cloth 2.0 Extension cord parts A. Power cable M male power (solderable) (Radio Shack) M female (solderable) (Radio Shack) 1/2 dual strand RCA audio cable 12ft (Radio Shack) B. Video cable BNC-male-to-RCA female connector (Radio Shack) 12' audio extension cable RCA male-to-female RCA gender changeer female-to-male (male on both sides) (Radio Shack) C. Cable ties and weatherproofing Bag of small black wire ties, 100 count (Ace Hardware) Black duct tape 12" length of small rubber tubing (Ace Hardware) Tools: Household solder and solder gun; small wire cutter, scissors 3.0 Other 12V DC power supply terminating in M male connector (Radio Shack) S-video capture device; for USB port laptops, e.g. - Pinnacle Dazzle Video Creator Plus (Home Depot) http://www.pinnaclesys.com/PublicSite/us/Products/Consumer+Products/Dazzle/Dazzle+Video+Archiving/Dazzle+Video+Creator+Plus.htm 8 1/2" x 11" black construction paper - to fabricate street-neighbor light blocking collar around camera head Capture software Optional: eyepiece dew heating strip, e.g. - Dew-Not heater strips, Scopestuff DN03 to DN05 http://www.scopestuff.com/ss_dnot.htm The Sony ExView HAD camera board radiates a substantial amount of heat. It was not felt that supplemental heating would be needed to prevent the glass cover lens from dewing or frosting over during autumn, winter or spring operation. During summer nights, it may be that the weather proof housing is too sealed and may result in the camera exceeding its operating temperature. Possible modifications include loosening the glass cover during summer or drilling a small hole in the camera housing in order to allow heat to escape during summer. In winter, this hole can be plugged with a rubber stopper. 4.0 Assembly Time: Find parts - 3 to 4 hours; Assembly 2 to 3 hours Base and Head 4.1 Remove base plate using Phillips head screwdriver; remove cover; pry out reflector using a flathead screw driver. 4.11 Using Phillips head screwdriver in base, remove light sensor. In base, use wirecutters to cut wires for removal of existing Utilitech spot light household current wires. 4.12 Retain strain relief C-clamp from base, two 1-1/2" pieces of household current wire and one-half of plastic tubing underneath C-clamp. 4.13 In head, use Phillips screw driver to remove light contact points in bottom of head. 4.14 From PC402UXP camera board, disconnect existing power and video wire at small adapter plug on bottom of board. 4.15 Thread PC402UXP power and video wire assembly through wire hole in base; slip C-clamp and original plastic tubing over PC402UXP power and video wire inside base. 4.16 Put dab of bathroom caulk at wire port entry in base for weather seal. 4.17 Insert two pieces of household wiring around PC402UXP power and video wire and beneath C-clamp and plastic tubing (to give the wire sufficient volume). Tighten C-clamp for strain relief. 4.18 Reinsert non-function light sensor in base to complete weather seal. 4.19 Reinstall bottom plate in base. 4.20 Wrap two PC402UXP power and video wires (about 10 inches long) with wire ties and tape to make the cable a single unit. (The extension cord will be prepared later). 4.21 In the head, prepare pluck-foam piece to insert in head. By experimenting, adjust height of plug foam so the camera lens will rest just below the cover glass. 4.22 With serrated kitchen knife, cut plug foam insert from one edge to center. 4.23 Using the microscrew driver on the PC402UXP camera board, loosen the retaining screw in side of the threaded lens mount. Remove the existing 90 degree TFOV pinhole lens from the camera board. 4.24 Install the 160 degree TFOV 1.68mm Edmund Optics lens. Power up the camera board; adjust the focus; and then lock down the retaining screw on the camera board. (Then lens shown in Figure 4 uses a separate locking ring (seen below the lens in Figure 4), but this was used only because the retaining micro-screw was dropped and lost.) 4.25 In head, thread PC402UXP power and video wire assembly up through the middle of the pluck foam; insert pluck foam into head. 4.26 Plug PC402UXP power and video wire assembly back into the camera board. 4.27 With hacksaw, cut reflector bottom down in height. By experimentation, judge the height of the cut so that the camera will be trapped between the reflector and the plug foam with light pressure. 4.28 Cut two notches in the rim of the reflector at 90 degree angles. There are used to install and pry out the reflector during final assembly. 4.29 Wrap the bottom half of the cut reflector in duct tape, so it will not damage or short-out the camera board when installed. 4.30 To fabricate the sunlight guard from black construction paper, take the Utilitech glass head cover and on scrap cardboard draw a circle around the head. Bisect two chords on the drawn circle to find the center of the circle. Using the pencil compass, measure a circle diameter about 3/8 inch larger than this circle. 4.31 Draw this circle on black construction paper. Cut the circle out of the paper. Fold the paper circle into quarters. 4.32 Measure the diameter of the camera lens. Cut the center-tip of the folded paper circle so a hole is created at the center of the circle. 4.33 Cut the paper circle on a line between the edge and center of the circle. 4.34 You now have the parts fabricated shown in Figure 6. 4.35 Do final assembly of the head. Install camera and reflector into head. A flat head screwdriver inserted into the reflector notches can be used to lever the reflector so it snaps home within the top of the head. Wrap the sun-light-guard black-construction-paper circle around the base of the camera lens. Use scissors to cut-off any excess paper from the edge of the sun light guard. 4.36 Power up your camera and check the final focus of the lens. Lock down the adjusting screw on the side of the camera board threaded lens housing. 4.37 Clean the camera lens and the Utilitech glass cover with ph neutral lens cleaner and glass cleaning cloth. Install the Utilitech glass cover. Install the dust cap (sewer pipe cover on the parts list over the head). 4.38 Slip the plastic pipe over the bayonet of the Utilitech base. Insert the cork in the bottom of the pipe. Press on the entire unit on a firm surface with the cork down. This will seat the cork into the bottom of the bayonet. The cork and pipe can be removed were it is desireable to field install the all-sky camera at a remote site by forcing the bayonet into the ground. Extension cord 4.39 Install the BNC-female-to-RCA-female adapter into the PC402UXP BNC video terminating connector. 4.40 Take the 12 foot single wire RCA speaker extension cord with one female end and one male end. Insert the male end into the BNC-to-RCA terminating connector. Insert the RCA-female-to-male gender changer into the female end of the RCA cord. You now have completed fabricating the video feed extension that terminates as the top connector in Figure 4. 4.41 Now begin fabricating the power extension cord shown in Figure 8. Take the 12 foot dual wire RCA speaker extension cord with a total of four male adapters (one male connector on each end the two wires). Split the cord down the middle so you have two single strand cords, each with a set of male RCA connectors on the end. 4.42 Using the wire cutters, cut the male RCA connectors off of each end of a single strand of the wire. Using the wire cutters, strip one end of this cable to exposure the two shielded strands of wire within the cable. 4.43 Solder the M power male adapter on to one end of this cable. Insert it into the female M power terminating connector of the PC402UXP camera board. 4.44 You now have the completed camera assembly with the completed video extension cord and a partially completed power extension cord hanging from one side. 4.45 Now bind the two cords together. (We will complete the terminating end of the power extension cord later.) Place the cord ends nearest the camera across your lap. Using the wire cutters, plastic wire ties and black duct tap, secure the two wires together every 6" to 8" inches with the wire ties. Use the wire cutters to clip off any excess leader from the plastic wire ties. Between each set of plastic wire ties, wrap the cords together with duct tape. Continue this process until you reach about 8" from the end of the video and power extension cords. Add two or three extra plastic wire ties at the cord ends for strain relief. 4.46 Solder the female M power connnetor on to the end of the power cords. This is the lower cable termination shown in Figure 5. 4.47 Plug the 12V DC power supply into the female M power connnetor. See Figure 5. 4.48 Split the 12" length of rubber tubing down the middle (on one side). Wrap the tubing around the exposed BNC and RCA connections near the base of the camera and extension cords. Wrap the rubber tubing with black duct tape to complete weather sealing the extension cord assembly. 4.49 You now have the completed unit shown in Figures 3 and 1. 5.0 Other possible design improvements 5.1 Drill a small hole in the head and plug it with a rubber stopper. The stopper can be removed during the hot summer months to allow heated air to escape from the head. 5.2 Drill and tap two holes on the plastic pipe so the camera can be easily attached to a telescope dovetail bar. Then the camera can be installed on a telescope mount for capturing tracked images of the radiant. 5.3 The PC402UXP camera board puts out its own heat, so frosting or dewing of the glass cover should not be a problem. If it is, provide supplemental heating by strapping a Dew-Not eyepiece heater around the glass cover.